We Give You The Knowledge To Be Successful

As low as $2.00 per square foot

What if you could say goodbye to the days where you need to break the bank to get a finishing job on your concrete?

 

Well, with the right products and right knowledge, you could save literally thousands of dollars.

 

So we set out to educate and provide the tools you need to make that floor look like you want it to.

 

With the Concrete Epoxy Flake System, you pick what you need for your specific project, order exactly the right quantity of exactly the right product you need and then get step by step instructions on how to apply it.

 

Contractors, business owners, homeowners, whoever you are, you'll get a straightforward way to get the job done.

There are 8 products you can apply to your Epoxy Flake System. 

concrete polishing pads kansas city

Satellite pads are required to get the Concrete Surface Profile needed to get the sheen you want.

Luckily, we provide the package pre-built with the grits you will need to get the CSP necessary for your polish job.

concrete surface cleaner

Super Blue quickly penetrates and dissolves lime deposits, mortar, scale, rust stains, etc. Used during the prep process to clean and remove contaminates, leaving you with the finish you're looking for.

 

Dilute 1:9 with water. When diluted, covers 1500 Square Feet per gallon (150 non-diluted).

M.V.B 100 is a high performance epoxy primer system designed to reduce water vapor transmission. When applied to a properly prepped concrete, this improves adhesion to concrete surfaces where moisture is an issue and other high performance coatings have failed.

 

Covers approximately 200 Square Feet Per Gallon

Epoxy Flo 100 is a professional grade epoxy coating. It is a 100 percent solids clear epoxy that can be used for a variety of purposes, such as tinting with pigment for solid color floors, mixed with metallic pigments, used as a broadcast coat, or used for a topcoat.

 

Covers approximately 100-125 square feet per gallon for the Epoxy Flake system (note, if you are using metallic Epoxy System this will affect the coverage area).

Epoxy Flow 100 Pigment is a high solids concretrated tint system specially formulated for Epoxy Flow 100. The color pack is formulated with high quality, ultra fine particle pigments that easily disperse in Epoxy Flow 100.

 

Use 1 per 3 gallon kit of Epoxy Flow 100.

Epoxy Flake are color chips for the Concrete Epoxy Floor Coatings System. These decorative flakes create a slip-resistant floor while bringing a splash of color to all floor coating projects.

 

Full broadcast coverage: requires 12% of your total square footage in pounds.

polyaspartic coating

Poly 80 Slow is our new, two-component Polyaspartic Aliphatic Polyurea utilizing innovative nanotechnology. It provides a high gloss clear coating.

 

Covers approximately 150-300 square feet per gallon.

The Epoxy Tools Kit contains all the items you need for the Epoxy job so you don't have to go hunting for everything. Save yourself some time!

 

Contains:  (2) Chip Brushes (2) 18″ Roller Covers (1) Adjustable Roller Frame (1) Set of Spike Shoes (1) Paint Mixer (2) 18″ Serrated Squeegees (1) White Pad (1) Sanding Screen (2) 5 QT Mixing Buckets

There are four steps to the entire process. You can download and print off these instructions here.

 

Step 1 - Prep the floor

 

1) Prepare the floor with our Concrete DNA Satellite Pads; 30 Grit

2) Run the pad with plenty of water under a low speed floor machine

3) Add a dilution of 1-Part Super Blue to 9-Parts water to floor to help open the concrete.

4) Squeegee water and remove from the floor with a wet/dry vac

5) Insure the floor is clean of dust and footprints by lightly mopping

6) Let the floor dry

 

 

 

 

 

Step 2 - The Prime Coat

A prime coat is optional but highly recommended. M.V.B. is a moisture vapor barrier and will help give better adhesion and better protection against moisture coming up through the concrete.

1) Use a 3/8” nap roller to apply the prime coat of M.V.B.

  • Let this coat dry until it is tack free Recoat time is 8-24 hours. Please note that if you wait 24-hours you will need to use a sanding screen to allow for proper adhesion of the next coat.

 

 

Step 3 -  BASECOAT & FLAKE

All mixing should be done mechanically with a mixing paddle.

1) Mix Epoxy Flow 100 with the pigment at a ratio 2:1

 

2) Use a serrated squeegee to spread the epoxy evenly and back roll; walk throughout the epoxy with your spiked shoes. Pictured below.

 

 

3) Broadcast your flakes using multiple high broadcasts to completely saturate your floor. Full broadcast is 12% of your square footage. I.E. 800 sq.ft. = 96 LBS

 

 

 

 

Step 4 - TOP COAT POLY 80 SLOW

 

1) After the base coat with the flakes has sufficiently set and is no longer tack free; typically, 10-16 hours run a sanding screen over the top to knock down jagged flakes

Poly 80 Slow is a 1:1 mix ratio. Protect the area from traffic until the coating has sufficiently dried.

3) Apply a clear top coat of Poly 80 Slow with an 18” 3/8” nap roller.

 

Empty tab. Edit page to add content here.

In addition to the step by step instructions, use the videos below to make sure you get the finish you want the first time you go through.

How to add pads to a low speed floor buffer

Concrete surface profiles needed

Application Method For Epoxy Floor

Prep For An Epoxy System

Applying Flake

Build Your Epoxy Flake System

Concrete finishing jobs are relative to the job, and no two jobs are the same! Use the information provided above to select the products you need, then select “Add To Cart” and get everything you need for an Epoxy Flake job shipped to your front door.

Concrete DNA™ Diamond Satellite Pads

$66.15$136.50

  • Makes polishing concrete super easy and FAST!
  • Many use our 30 grit for prepping a floor for stain and seals or before applying a coating

Check out Concrete Surface Profiles to see what grit you need to get your job done.

Fast Same Day Shipping

Free Shipping Over $200

Clear

M.V.B 100 – Moisture Mitigating Epoxy Primer

$52.00$257.25

Covers 200 Square Feet Per Gallon

Fast Same Day Shipping

Free Shipping Over $200

Clear
SKU: CFS-M.V.B Categories: ,

Super Blue | Concentrated

$33.00

Fast Same Day Shipping

Free Shipping Over $200

In stock

SKU: 787639248354 Categories: ,

U Epoxy It ™ | Epoxy Flow 100

$40.00$899.00

  • Low VOC (Volatile Organic Compounds)
  • 100 Percent Solids
  • Great flow characteristics…perfect for metallics, and broadcast coats

Fast Same Day Shipping

Free Shipping Over $200

Clear
SKU: CFS-EPOXY FLOW 100 Categories: ,

Epoxy Color Pigment

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

$30.00$35.00

Fast Same Day Shipping

Free Shipping Over $200

Clear
SKU: CFS-EPOXY-PIGMENT Categories: ,

Poly 80 Slow

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

$55.00$1,361.50

  • Excellent top coat with great work time…up to 1 hour!
  • UV Stable
  • High Gloss..super clear
  • Superior bond strength

Fast Same Day Shipping

Free Shipping Over $200

Clear
SKU: CFS-ASPARTIC-80SLOW Categories: ,